Top Common Plumbing Problems That Plumbers In Swords Will Get Fixed Effectively!

Top Common Plumbing Problems That Plumbers In Swords Will Get Fixed Effectively!

Home Plumbing is an aspect to which homeowners pay very little or no attention. Taking care of your faucets fixtures and drainage is difficult at times, but it can prove to be fruitful when done right. There is no denying that conventional wisdom is passed down from one generation to another. Unfortunately, often homeowners believe a few myths that do no good, instead cost them money. 

Problems associated with plumbing are inevitable at times. You may face a few issues due to aging fixtures or general wear and tear of plumbing equipment. A few other problems are caused by the maintenance and usage of specific systems. If you are in Swords and want one of your faucets or fixtures fixed, New Century Plumbing is the best solution. With years of experience, the plumbers in Swords Dublin have seen and fixed almost all kinds of plumbing problems.

Call for Plumbers In Swords Dublin When You Face These Plumbing Problems

You must have come across many facts that are nothing but straight myths. For instance, a lemon slice can freshen up your drain, or you should run water while disposing of the garbage down the drainage. These are of no help. Instead of harming your drainage system by following these myths, choose to call for an expert. They are well versed to deal with all plumbing problems. 

 Leaky Pipes 

Leaky Pipe is a widespread problem caused by several kinds of issues such as corrosion of pipes, stubborn clogs, excessive water pressure, damage of pipe joints, etc. No matter why your pipe is leaking, the problem needs to be fixed at the earliest. The longer you ignore those leaky pipes, the more damage they will cause to the plumbing system.

Dripping Faucets

Such faucets are wasteful, annoying, and costs considerably. At times, the drip is caused by an O ring or a worn-out washer, and you can easily replace them. However, if this is not the case, your faucet may also drip because of improper installation or corrosion. If you see that your faucet is dripping, consider calling the best Plumber Swords to get them fixed at the earliest. 

Low Water Pressure 

When your plumbing system experiences weak water pressure, it becomes quite difficult for you to use the entire plumbing system. The weak water force is often due to a bigger plumbing problem like clogs in the sewer or drains, pipe corrosion, blocked or cracked sewer lines, and hidden water leaks in your home, etc. In such a scenario, you can consider calling best Plumber Swords to fix this issue.

 Failure of Sump Pump

 The Sump Pump failures are often caused because of a problem with the unit or any external issue. There are numerous causes of Sump Pump failures that include: 

○ Presence of a huge amount of water, for instance, heavy rain. 

○ Stuck Switches. 

○ Improper installation of Sump Pump. 

○ Clogs in discharge pipes.

○ When the Sump Pump is around ten years old, it is prone to failures. 

Leaks in Hose Bibb

 Leaks in the Hose Bibb are common during the spring and summer seasons. After cold and long winters, if homeowners don’t protect their Hose Bibbs, they get cracked and, as a result, begin to leak. New Century Plumbing advises its consumers to invest and install a frost-proof hose bibb. It is believed to have reduced the chances of leaks in the future. 

 Running Toilet

 Are you aware that a running toilet can waste almost 200 gallons of water in a day. It is a considerable wastage of water, and therefore, you should choose to get it fixed at the earliest. Plumbers in Swords Dublin from New Century Plumbing will help you get away from such problems at the earliest. There are several reasons because of which you may experience running toilets. For instance, inadequately sized flapper chains, refill tube problems, corroded toilet handles, and worn out flush valves or flapper seals. 

Clogged or Slow Drain

 Problems faced in the drainage system are hazardous to health, and they may even cause plumbing disasters if you ignore them. When you have one slow or clogged drain in your home, it means that there is a problem in the drainage system of that area. Routine cleaning of drains is the solution to get rid of such issues. 

Multiple clogged or slow drains sign a problem in the sewer line. You should call for a plumbing expert whenever you notice multiple slow drains in your home. 

Should You Hire Services of Plumbers in swords?

Save your money and call for expert Plumber Swords to get all your plumbing problems fixed. Take good care of your fixtures, faucet, and disposal, and they will last for a long time. Plumbing problems are widespread in every household, but some are more common than others. No matter what issue you face with the plumbing system, New Century Plumbing will get them all fixed at the earliest. 

Is Your Radiator Not heating? 4 Things That You Can Do To Get The Issue Solved

Is Your Radiator Not heating? 4 Things That You Can Do To Get The Issue Solved

With the night getting darker and the weather getting cold, we rely upon only one thing: our central heating system! Wouldn’t it be annoying to find your radiator cold even after heating it for around twenty minutes?

If your radiators are not heating sufficiently, then there is a problem with the boiler or the central heating system. Moreover, if you notice some of your radiators are heating up while some are not, there is a possibility that there are some underlying serious issues. 

If you notice your radiator not heating up, then the first thing you need to do is determine whether there is a problem with one or more radiators. It will help you get to the bottom of your problem. 

This article discusses a few simple steps that will help you understand the root of the problem and a few fixes to get the radiators to heat your home again. Often, the radiators don’t heat up because of some simple issues that can be resolved effortlessly. Without further ado, let us have a look at simple steps that will help homeowners to get a warm and toasty home in no time.  

Check If There Is Trapped Air And Let Your Radiators Bleed. 

If you notice that just one of the house radiators not heating up, it must be because of some trapped air. If you do not turn on your radiators for quite some time, air gets trapped in them. In such a scenario, the radiators get warm only at the bottom and remain cold at the top. If this is the case, you will have to let your radiators bleed.

For this, you will have to use the radiator keys and unscrew the bleed screw a bit. Keep unscrewing until you hear a hissing sound. After the sound disappears, water will start coming out from the radiator. Now, close the bleed screw and turn on the device. Your radiator will now start getting warm.  

Check For Considerable Problems With The Boiler And Central Heating 

If you have resolved the small issues, and the problem still persists then check for some more severe issues that your system might be facing. If none of your radiators is heating, it could be a sign that there is some serious issue. 

If the water in the system is not getting hot, you should call for professionals. System experts will get to the root of the house radiator heating issues and fix it. Please notice everything unusual about your heating system and tell the plumber about it. Look out for the signs and the weird noises.

Find Out If Your System Needs Power Flushing 

If you cannot find out the root issue, there are possibilities that the system just needs a power flushing service. Power flushing is the process of getting sludge and debris removed from the radiators. Over time, sludge and debris get stuck in the central heating system and affects its performance. 

A denotative sign that your system needs power flushing is that your radiators will get heated up at the top but not at the bottom. The sludge present in the bottom region will restrain the radiators from getting heated up properly.  

Check the Valves of your Radiators 

If your radiators don’t have any trapped air and its entire surface is cold and not just its top, then consider checking your radiator’s valves. Ensure that both the left and right valves are open. If your radiator has a valve that allows you to set the temperature automatically, you should ensure that the radiator is operating at an optimum temperature. Thermostatic radiators cause the system to stop working when it gets seized up. If such a problem arises, you should get in touch with an engineer.  

Final Thoughts 

It is annoying if you find out your radiator not heating one fine day. There are many possible causes and solutions with the help of which you can get your radiators working again. However, if none of those as mentioned above tips works, it is recommended that you call radiator technicians right away.  

Underfloor Heating vs Radiators? Which One Is Better?-  Our Guide

Underfloor Heating vs Radiators? Which One Is Better?- Our Guide

Thanks to technology, there are heat emitters which will help you walk freely in your house no matter how cold it is. However, considering the many options available, how do we decide on which is the best heating system?

Choosing the perfect heating system for your home can be a bewildering process. It also involves a huge investment and hence you cannot afford to take an impulsive decision. Apart from keeping your family’s comfort in mind you need to evaluate various other factors like cost, climate, capacity, efficiency, area, safety etc. We conducted a research on the two most popular heat emitters- Underfloor Heating and Radiators based on all the factors.

Let’s have a look.

What is Underfloor Heating?

This is one smart way to heat up your home. Underfloor heating system is installed beneath the floor which will in turn emit heat evenly in your house. Apart from experiencing a warm floor, this will facilitate energy efficiency and reduce carbon emissions. The heating system is one of the oldest forms of central heating. The heat generated is monitored by a thermostat to maintain consistency in the temperature.

How does it work?

Underfloor heating system comes in two forms- water and electric system. The water system pumps heated water beneath the floor through a circuit of pipes. It should be installed while constructing a new floor.  In the electric system, electric coils are installed underneath the floor. This is effective for smaller areas and is controlled by a timer.

Advantages of Underfloor heating system:

  • Even and consistent distribution of heat even at a larger space
  • It is concealed so won’t spoil the house décor
  • Amplified sense of luxury and hygiene
  • Efficient functioning as it works on low temperature

Disadvantages of Underfloor heating system:

  • High on installation expensive
  • Takes long to heat a room
  • Restriction on some furniture or fittings
  • Installation can be inconvenient

What are Radiators?

Radiators, made from metal, are heat exchangers which transfer thermal energy from one channel to another. You don’t have to worry about the outside weather anymore as this heat emitter will keep you warm at any temperature. This is one of the most effective and desirable heating systems.

Central Heating 

How does it work?

There are two types- Steam and Hot water radiators. Steam radiators are attached to a boiler which heats up the water until it forms into steam. This steam travels up through an upright pipe to the radiator which in turn heats up the room. Hot water radiator, as the name suggests, has the heated water (from a boiler) running through the supply pipes into the radiators.

Advantages of Radiators:

  • Low on maintenance
  • High level of safety
  • Extremely reliable and quick
  • Can be portable from one room to another

Disadvantages of Radiators:

  • Loud and Noisy
  • Cool down quickly
  • Would require adequate amount of ventilation in the room
  • Becomes hot while functioning
  • Heat is not distributed evenly
  • Cheap radiators can spoil the aesthetics of the room


After discussing the functioning of the heat emitters, pros and cons we can conclude that both have their advantages and downfalls. Radiators were the most obvious choice in the past. However, Underfloor heating will give you the privilege of enjoying your own home. If you are not tight on your finances, we would recommend you to bring home the Underfloor heating system. This versatile equipment, with its even distribution of hot air, will let you walk warm feet comfortable in your entire house. It will not only keep your room cosy throughout but also maintain the aesthetics of your house. Lastly, you do not have to stress too much about the electricity damages. You can save up the extra bucks there.

The Shower Doctor: Electric Shower Not Getting Hot

The Shower Doctor: Electric Shower Not Getting Hot

A hot shower is all you need to relax your body and mind, especially after a long day’s work. It is the best therapy to give you a good night’s sleep and ease your muscles. Imagine yourself to have soap on you and the shower does not heat up. That could be infuriating isn’t it? 

If you are going through this most common problem of your electric shower not getting hot, you are on the right page. We are here to explain to you why your shower water isn’t getting hot in spite of being equipped with a hot water heater. 

Stay tuned to know it all.

  • Temperature Control

This is the most common and minor issue.All you have to do is set the temperature of the heater correctly. If your electric shower is not getting hot, the problem could be lying in the temperature control. A minor damage in an electric water heater can also lead to other issues like- the water would get heated up only for a short time or not get hot at all.  

  • Faucet Check

Figure out if the problem is in the entire house or just the shower. Examine the heat temperature by turning on every hot water faucet at home. If all of them get hot but cool quickly, there is an issue with a burner in the heater. If they do not get hot at all, the issue is a defective dip tube. However, if you see no issue in any of them, then the obstacle lies within the shower components. So do a faucet check at home.

  • Shower Valve Defect

Shower valves are fittings fabricated to control the temperature and water flow. The ultra-fashioned shower valves can make showering a pleasant experience for you. They quintessentially blend cold and hot water to give you the most ideal temperature. In case of the o-ring wearing out, the shower valve will not do its job. It will no longer do the proper blending of temperatures.  So get your shower valve repaired at the quickest you can. 

  • Long usage

Hot water heaters usually have a time limit to generate the expected heat. If you keep it on for a long period, your electric shower will not get heated up after a certain time period. Beyond its cut off time, the shower will give out cold water.   

  • Tank Size

If you are running out of hot water and have too many members at home, the tank size could be an issue. A small hot water tank could be inadequate to suffice everyone. 

Try out these following steps to solve the issue within your confined space:

  • Check your power supply 
  • Be sure of the isolator switch being on
  • Fix the blockage in the shower drain, if any
  • Take care of any leakage in the inlet pipe
  • Use a large tank unit
  • Use eco mode
  • Take shorter showers

Once you recognize the problem, you  can determine how to fix it. If your electric shower is still giving you issues and none of the above work, call an expert. 

Running out of hot water? Put an end to it today!

How To Fix A Dripping Tap?

How To Fix A Dripping Tap?

If you have a dripping water tap in your home or even at your workplace, there would be several reasons you want to fix it. Isn’t it? First of all, water is a scarce natural resource and there are many studies, organizations and influencers talking about how we should avoid the wastage. Water wastage being the primary reason for not letting the water keep dripping from the tap, there are more reasons as well.

The continuous noise of water drops or water stream (if the dripping is prolonged) is pretty annoying and the first thing you would want to achieve is a silent water tap when not functional. Thirdly, running water or dripping water also cause damage to the sanitary equipment. In case the dripping is serious, leakage of water may also cause heavy damage to the property as well.

Let’s have a detailed overview of how to fix a dripping tap, some basics to identify the extent of damage and then take measures accordingly. Before that, if the leakage is unnecessarily higher than usual dripping, you must seek professional plumbers help ASAP and should not try to attempt to fix it using your own knowledge. Some fixes may require technical understanding of the equipment, therefore before starting to make an honest judgement and proceed accordingly.

What do you need to get started on how to fix a dripping tap?

First of all, you need to check if you have all necessary tools in your toolkit at home. If not, get them first and ensure you have all the required equipment to fix the dripping tap. Majorly what you need is provided below:

  • Screw driver
  • An adjustable spanner
  • Pipe wrench
  •  Replacement of damaged washer(s) or replacement of disc cartridge

It is better to keep some thread, tape or a consolidated kit nearby for any unexpected findings after you open the dripping tap.

Before you start to fix the dripping tap, make sure that the water supply to that particular tap or to the entire place is disconnected. Also, since you will still find some running water in the water supply pipe, make sure you have covered yourself and the equipment nearby for safety. In addition, also ensure that there are no electric wires or open sockets nearby the damaged or dripping tap.

Determine the water tap type

There are many types of water taps that are now-a-days available in the market and they vary on shape, structure and operating mechanism. A couple of common types that we can use here to guide you on how to fix a dripping tap are:

If you have a traditional two level water tap, you can determine which side causing the dripping and open that end. Traditional water taps cause dripping mostly when rubber seal or washer is damaged. If you have the single adjustable lever, it will be fixed by replacing the ceramic cartridge beneath the lever.

Get started with how to fix a dripping tap

Step # 1 Remove the Screws

No matter what type of tap you have, first thing first you need to find the screws that have fixed the top cover of the tap or the lever of the tap. Depending upon the model the screw can be located either beneath hot/cold water levers or beneath the temperature indicator.

Once you find the screws, remove them and remove the water tap head. There may be additional parts before you can see the ceramic cartridge or the washer, in order to put them back in the same sequence make sure to align them in the same flow as you remove those.

Step # 2 Remove Washer or Remove the ceramic cartridge

Again, depending upon the water tap type, you either need to fix and replace the rubber seal or washer for traditional tap or ceramic cartridge for monobloc water tap.

Removing and replacing washer

If you have a traditional water tap, take an adjustable spanner and use that to hold the brass valve. Once you have established a firm grip, start rotating that and keep on rotating until it is loose enough to remove.

Remove the washer and inspect for possible next steps, either it is fully damaged to be replaced with a new one or it requires cleaning. Do the necessary fix and place the cleaned washer or new washer in place, following the same way that you used to remove it.  

Removing and replacing O-Ring

Next for the traditional water tap dripping fix, you may need to replace the O-ring which exists beneath the spout and is slightly bigger than the washer. You may need a flat screwdriver to get it out or scissors to cut it off and put a new one in place.

Once the O-ring is removed and replaced, put back the remaining water tap components as you removed them.

Removing and replacing ceramic cartridge

Lastly, if you have a monobloc water tap it will require replacement of ceramic cartridges to fix the dripping tap. Take an adjustable spanner and remove the brass valve same as you did for removing the washer. Unscrew the damaged ceramic cartridge, pick the replacement and screw the new cartridge until you feel it is tight enough and cannot be moved further. Place back the water tap components as you removed them.

Once the fixed tap is in place, turn on the water supply and check if the issue is fixed. This is the basic guide that you can follow to fix a dripping tap anywhere in the house, out in the garage area or any other place. For better results, keep the removed parts either numbered or in a sequence of how you remove it and then perform the screwing back of components to the maximum level where you cannot move them further. Let us know if you know any key tips that our users must follow if you want to know how to fix a dripping tap.

Mira Electric Shower Installation

Mira Electric Shower Installation

Mira electric shower installation – a user-friendly guide with tips & tricks.

Mira electric showers launched in the market in 2008 but the manufacturers did a relaunch of the Mira electric showers again in 2014, both the functionality and look & feel of the product was altered to meet better customer expectations. Since 2014, there is no change to the Mira electric shower and the same version of the electric shower is in market.

Mira electric shower installation guide comes as part of the packaging box. For any reason if your packaging box does not contain it, you can watch the YouTube tutorial to install the Mira electric shower. However, not everyone may have the time to follow video instructions or would understand the technical wording being used in most of the tutorials.

Here in this article we are going to share some tips, tricks and a basic guide Mira electric shower installation at home with basic instructions to follow. Here are some tips that you must foresee before initiating the installation process.

  • Check Product Condition

A lot of people are buying products online as well as getting them dispatched to their homes by third party service providers. As soon as you receive the product, make sure you film the unboxing process and thoroughly check for any possible issues/breakage.

  •   Decide a Location

Carefully select a central point where you need the electric shower installation done. Of course, it will be one of the washrooms of the house but in there, you have to look for the location where there are no electric sockets nearby and no safety hazards of any sort. 

  •  Check the Location for Electric/Other Wiring

Mira electric shower installation Process

Once you decide on the location of installation of Mira electric shower, still use a stud or metal detector to check the backend of the wall. This is a critical step to check whether there are electric wires or any other supply pipes at the back of the selected wall.

Once you have checked these initial steps for a safe and secure Mira electric shower installation, only then move forward to the actual installation process of the product.

Step # 1 Ensure that main power supply is disconnected

Step # 2 Use the template to align the installation plan

The packaging of Mira electric showers comes with a template design, which you need to follow and put on the wall to dig all the required holes for the electric shower installation. In addition, you will also need a spirit level checker to balance the holes at the right location.

You will be required to make holes in the template first for all electric and any other pipes and the wall plugs to fix it. Once done, place that on the wall and make actual holes through the wall for fixing it. The ceiling of the room should be at least 200 mm above the top surface of the Mira electric shower.

Step # 3 Remove the cover from Mira Electric Shower

Next step you have to remove the screws from the top and the bottom of the product body. By removing the screws you will be able to remove the top cover of the product and will be able to see the product design for better fixing and Mira electric shower installation.

Step # 4 Determine the inlet of water supply

Once you place the naked product on the wall, determine the location and direction of water supply. Before you link the water supply to the Mira electric shower, make sure to flush the pipes and remove any debris if needed.

Step # 5 Let the water run through the product

Once the water supply is flushed and linked, secure the wall plugs and fix everything. Do a final check to see if there is any water leakage of any sort. Once you are sure there aren’t any, only then insert the power cable on the designated link and run it to the main terminal for power supply.

Step # 6 Check if the power terminal is working

Wear safety shoes or gloves, whatever is necessary and turn on the electric supply. Check if the product is working fine and once it looks fine, attach the top cover back and fix the bottom & top screws as removed in the first place.

This is pretty much it about the Mira electric shower installation that you need to know and perform for a safe installation. However, there may be loopholes in water supply, electricity connection or any sort of issue which will not let the product work fine in the first go. In such cases, you may go to the video tutorials and check every step visually before making a lot of effort. In case you are still unable to figure out the source of the issue, better call for professional help rather than redoing it again and again.